Technical Information & Details of the MEAN WELL PWM-60-24KN LED Driver Output Power: 60 W Output Voltage: 24 V DC Output Current: 2.5 A Dimming Range: 0 – 100 % (PWM dimming) Minimum Dimming Level: 0.01 % PWM Output Frequency: 200 – 4,000 Hz, user‑changeable via ETS Input Voltage Range: 90 – 305 V AC / 127 – 431 V DC Input Frequency: 47 – 63 Hz Power Factor (typ.): > 0.97 @115 VAC, > 0.95 @230 VAC, > 0.92 @277 VAC (full load) Efficiency (typ.): approx. 89 % AC Input Current (typ.): 0.8 A @115 VAC / 0.4 A @230 VAC / 0.32 A @277 VAC Inrush Current (typ.): 50 A @230 VAC (cold start, twidth ≈350 μs, per NEMA 410) THD: < 20 % (≥60 % load @115 / 230 VAC; ≥75 % load @277 VAC) Standby Power Consumption: < 0.5 W Overload Protection: 108 – 130 % of rated power, hiccup mode, auto recovery Overvoltage Protection: shut down output, re‑power on to recover (typ. 28 – 34 V DC) Overtemperature Protection: shut down output, re‑power on to recover Short‑circuit Protection: hiccup mode, auto recovery Operating Temperature (case): −35 °C to +85 °C (derating according to “Output load vs. temperature” curve) Operating Humidity: 20 – 95 % RH, non‑condensing Storage Temperature / Humidity: −35 °C to +80 °C, 10 – 95 % RH Temperature Coefficient: ±0.03 % / °C (0 – 50 °C) Vibration Resistance: 10 – 500 Hz, 5 G, 12 min./cycle, 72 min. along each X, Y, Z axis Dielectric Strength: 3.75 kVAC (input–output) Isolation Resistance: > 100 MΩ @500 VDC, 25 °C, 70 % RH Safety Standards: ENEC EN 61347‑1, EN 61347‑2‑13, EN 62384 (independent), GB19510.1 / GB19510.14, BIS IS 15885 (Part 2/Sec 13 for 12/24 KN), EAC KNX Standards: Certified KNX protocol EMC Emission: EN 55015, EN 61000‑3‑2 Class C (≥60 % load), EN 61000‑3‑3, GB/T 17743, GB17625.1, EAC TP TC 020 EMC Immunity: EN 61000‑4‑2,3,4,5,6,8,11; EN 61547 (light industry level, 2 kV Line‑Line surge), EAC TP TC 020 MTBF (typ.): 2,135,200 h (Telcordia SR‑332, 25 °C) / 247,700 h (MIL‑HDBK‑217F, 25 °C) Dimensions (L x W x H): 150 mm x 53 mm x 35 mm Weight: approx. 0.45 kg Case & Protection: fully encapsulated plastic housing, IP67, Class II Cooling Method: fanless, free air convection Information about the MEAN WELL PWM-60-24KN The MEAN WELL PWM‑60‑24KN is a 60 W constant‑voltage LED driver with 24 V DC PWM‑style output and a fully integrated KNX interface, created for direct connection to KNX building automation systems without requiring a KNX‑DALI gateway. Its PWM constant‑voltage output allows 24 V LED strips and constant‑voltage LED lamps to maintain uniform brightness and colour appearance over long runs, even when dimmed deeply. Key strengths of the PWM‑60‑24KN include the very low minimum dimming level of 0.01 % and the user‑adjustable PWM frequency from 200 Hz up to 4 kHz via ETS, enabling setups that comply with IEEE 1789‑2015 “no risk” recommendations and EU Ecodesign SVM flicker limits. Combined with a typical efficiency of around 89 %, a wide 90–305 V AC input range and a fully potted IP67 plastic housing, the driver is well suited for long‑life installations in indoor architectural, decorative and ambient lighting applications where flicker and visual comfort are critical. The native KNX protocol support also stands out: the driver can be addressed and programmed in ETS, and the PWM KN series even supports ETS addressing/programming without AC mains connected, simplifying commissioning on site. Together with its broad case temperature range from −35 °C to +85 °C, robust protection features and international approvals, the PWM‑60‑24KN offers a compact, reliable KNX‑centrical solution for 24 V LED strip lighting, indoor LED lighting and constant‑voltage LED bulbs in smart building projects.

Technical Information & Details on MEAN WELL PWM-200-24KN Power Supply Output Power: 199.2 W Output Voltage: 24 V DC Output Current: 8.3 A Input Voltage Range: 100 – 305 V AC / 142 – 431 V DC, 47 – 63 Hz Efficiency: up to 93 % Inrush Current: 65 A (Peak) No-Load Power Consumption: < 0.5 W (Standby) Operating Temperature: −40 °C to +80 °C Cooling: natural convection Protection Functions: Short Circuit (Hiccup), Overload, Overvoltage, Over Temperature Isolation Voltage: 3.75 kV AC between Input and Output Dimensions (L x W x H): 195 mm x 68 mm x 39.5 mm Weight: approx. 1.03 kg Safety & EMC Certifications: UL8750, ENEC, EAC, CB MTBF: > 1658 K hours KNX Interface: certified, PWM Dimming up to 4 kHz Information on MEAN WELL PWM-200-24KN The MEAN WELL PWM-200-24KN is a high-performance 200 W PWM LED driver power supply with integrated KNX interface for smart lighting control in buildings. It excels with exceptional efficiency up to 93 %, wide temperature range from -40 °C to +80 °C, and universal input voltage for global applications. Unique KNX-certified integration enables seamless dimming (0-100 %, PWM up to 4 kHz), automatic fault recovery, and outstanding reliability with MTBF over 1.6 million hours – perfect for professional LED lighting in industrial, office, and smart home environments.

Technische Eigenschaften des MEAN WELL ELG-240-24DA Leistung: 240W Aluminiumgehäuse Integriertes PFC Standby Ladeverbrauch <0,5W IP67 DALI Erdung muss am Gehäuse durchgeführt werden! (Alternativ mit Erdungskabel die 3Y Variante wählen) Allgemeine Lebensdauer >50.000Std. 5 Jahre Garantie Produktbeschreibung zur MEAN WELL ELG-240 Serie Bei der MEAN WELL ELG-240 Serie handelt es sich um 240W AC/DC LED Netzteile, die im dualen Modus einen Konstantstrom- und Konstantspannungsausgang unterstützen. Die ELG-240 Netzteile arbeiten mit einem 100~305VAC Eingangsbereich und bieten verschiedene Ausgangsspannungen im Bereich von 24V bis 54V an. Dank des 93% hohem Wirkungsgrads und dem lüfterlosen Design kann die Serie unter freier Luftkonvektion im Temperaturbereich von -40°C bis +90°C betrieben werden. Durch das verwendete Aluminiumgehäuse und den Schutzklassen IP65/67 finden MEAN WELL ELG-240 Netzteile Anwendung sowohl Indoor-, als auch im Outdoorbereich. Die Serie verfügt weiterhin über verschiedene zusätzliche Funktionen, wie 3 in 1 Dimmung, Smart-Timer-Dimmung oder DALI, welche eine hohe Flexibilität in LED Beleuchtungsanwendungen garantieren.

Technical Information & Details for MEAN WELL PWM-90-24 LED Driver Output power: 90 W Output voltage: 24 V DC Rated output current: 3.75 A Output current range: 0 – 3.75 A (PWM‑modulated constant voltage output) Output type: Constant voltage, PWM style output Dimming range: 0 – 100% (3‑in‑1 dimming) Dimming interfaces: 0–10 V DC, 10 V PWM signal (100 Hz – 3 kHz), resistive dimming PWM frequency: approx. 1.47 kHz (Blank / DA type), 2.5 kHz (DA2 type) No‑load power consumption: < 0.5 W Input voltage range: 90 – 305 V AC / 127 – 431 V DC, 47 – 63 Hz AC input current (typical): 0.95 A @ 115 V AC / 0.5 A @ 230 V AC / 0.4 A @ 277 V AC Power factor (typical): > 0.98 @ 115 V AC, > 0.96 @ 230 V AC, > 0.92 @ 277 V AC (full load) Efficiency (typical): ≈ 90.5% Total harmonic distortion (THD): < 20% (≥ 60% load @ 115/230 V AC, ≥ 75% load @ 277 V AC) Inrush current (cold start): 60 A @ 230 V AC (twidth ≈ 550 µs, 50% Ipeak) Leakage current: < 0.25 mA @ 277 V AC Overload protection: 108 – 130% of rated output power, hiccup mode, automatic recovery Over‑voltage protection: ≈ 28 – 34 V DC, shutdown, re‑power on to recover Over‑temperature protection: output shutdown, re‑power on to recover after cooling Operating temperature (case range): −40 °C to +85 °C (see “output load vs. temperature” derating curve) Maximum case temperature (T-case max): +85 °C Operating humidity: 20 – 95% RH, non‑condensing Storage temperature & humidity: −40 °C to +80 °C, 10 – 95% RH Ingress protection: IP67, fully encapsulated Case material: fully isolated plastic housing Insulation class: Class II (no protective earth connection) Dielectric strength: input–output: 3.75 kV AC; input–DA: 1.5 kV AC; output–DA: 1.5 kV AC (DA/DA2 types) Insulation resistance: > 100 MΩ @ 500 V DC, 25 °C, 70% RH Vibration: 10 – 500 Hz, 5 G, 12 min./cycle, 72 min. per axis (X, Y, Z) MTBF: ≈ 2.39 million h (Telcordia SR‑332, 25 °C) Dimensions (L x W x H): 171 mm x 63 mm x 37.5 mm Weight: ≈ 0.77 kg Primary connections: AC/L (brown), AC/N (blue), pre‑wired input cable Secondary connections: Vo+ (red), Vo− (black), dimming / DALI leads (purple, pink depending on type) Recommended mounting: horizontal mounting, case type PWM‑90P, free air convection Safety standards: UL 8750 (except DA type), CSA C22.2 No. 250.13‑12, ENEC EN 61347‑1 / EN 61347‑2‑13 (independent), EN 62384, BIS IS 15885 (for 12/24/48 V blank and DA2 types), EAC, GB19510.1 / GB19510.14 EMC standards: EN 55015, EN 61000‑3‑2 Class C (from 60% load), EN 61000‑3‑3, EN 61547, EN 61000‑4‑2/3/4/5/6/8/11, GB/T 17743, GB 17625.1 DALI (DA / DA2 types): IEC 62386‑101/102/207/251, Device Type 6 (DT6), 16 groups / 64 addresses (DA/DA2 only) Lifetime: typ. > 50,000 h at T-case ≈ 75 °C Warranty: 5 years Information about MEAN WELL PWM-90-24 The MEAN WELL PWM‑90‑24 is a 90 W AC/DC LED driver with constant voltage PWM output that maintains uniform brightness across 24 V LED strips, even when several runs are connected in parallel and dimmed. With its 90–305 V AC wide input range, high efficiency around 90.5%, IP67 potted construction and case temperature rating from −40 °C to +85 °C, it is designed for robust, fanless operation in demanding indoor and protected outdoor installations. The integrated 3‑in‑1 dimming (0–10 V, PWM, resistance), optional DALI/DALI‑2 control, active PFC and long service life make the PWM‑90‑24 a strong choice for professional 24 V LED strip, decorative, architectural and industrial lighting systems requiring precise dimming and reliable 24/7 operation.

Technische Eigenschaften des SC Power KVF-24150-TDH: Leistung: 150W Spannung: 24V Ausgangsstrom: 6,25A Konstantspannungsausgang Eingangsbereich: 200-240VAC Arbeitseffizienz: bis zu 90% TRIAC Dimmer: Phasenan-/abschnittsdimmung/ Phase Cut Einfache Installation IP66 Design; Geeignet für Outdoor-Installationen Kühlung durch freie Luftkonvektion Schutz vor Kurzschluss, Überlast, Überstrom und Überhitzung Eingebaute PFC Funktion Perfekte Kompatibilität; Flimmerfreie Dimmung Geeignet für LED-Beleuchtungssysteme und Displayanzeigen

Technical Information & Details for MEAN WELL LCM-60KN LED Driver Output Power: 60.3 W Output Current: 500mA, 600mA, 700mA (default), 900mA, 1050mA, 1400mA (selectable via DIP switch) Output Voltage Range: 2 – 90 V DC (depending on selected current) Input Voltage Range: 180 – 295 V AC / 254 – 417 V DC, 47 – 63 Hz Efficiency: up to 91% Auxiliary Output: 12 V / 50 mA (ideal for sensors) Inrush Current: Cold start 20A (t_width = 260 µs) at 230 V AC Standby Power Consumption: < 0.5 W Operating Temperature: −30 °C to +90 °C (case temperature Tcase) Cooling: Fanless natural convection Protections: Short circuit, Over voltage, Over temperature (auto-recovery) Withstand Voltage: 3.75 kV AC between input and output Dimensions (L x W x H): 123.5 mm x 81.5 mm x 23 mm Weight: approx. 240 g Certifications: ENEC, UL8750, CB, EAC, KNX certified Interface: Integrated KNX interface & Push dimming Manufacturer Warranty: 3 years Information about the MEAN WELL LCM-60KN The MEAN WELL LCM-60KN is a high-performance 60W LED driver specifically engineered for seamless integration into KNX building automation systems. Featuring a built-in KNX interface, it eliminates the necessity for complex KNX-DALI gateways, significantly reducing installation time and overall project costs. A key advantage is its multiple-stage constant current output, selectable via DIP switches between 500mA and 1400mA. This flicker-free design provides premium light quality, ensuring visual comfort in professional office environments and high-end architectural projects. Beyond standard dimming, the unit supports advanced features like Constant Light Output (CLO), operating hours monitoring, and energy consumption feedback transmitted directly to the KNX bus. The driver also includes a built-in 12V auxiliary DC output for powering smart sensors and allows for the synchronization of up to ten units for uniform control of large lighting zones. With its slim Class II plastic housing and compliance with emergency lighting standards, the LCM-60KN is the ideal choice for intelligent smart-building infrastructures, capable of reliable operation at case temperatures up to 90°C.