Technical Information & Details of the MEAN WELL PWM-60-24 LED Driver Output power: 60 W DC output voltage: 24 V DC Rated output current: 2.5 A Output type: Constant voltage PWM style output Dimming range: 0 – 100 % (3‑in‑1: 0–10 VDC, 10 V PWM signal, or resistance; DA/DA2: DALI/DALI‑2) PWM output frequency: approx. 1.47 kHz (Blank/DA) / 2.5 kHz (DA2) Overvoltage protection threshold: 28 – 34 V DC Setup / rise time: ≤ 500 ms, 80 ms @ 115 / 230 VAC (full load) Hold‑up time (typ.): approx. 16 ms @ 115 / 230 VAC (full load) Input voltage range: 90 – 305 V AC / 127 – 431 V DC, 47 – 63 Hz Power factor (typ.): PF > 0.97 @ 115 VAC, PF > 0.95 @ 230 VAC, PF > 0.92 @ 277 VAC (full load) Efficiency (typ.): approx. 89 % AC input current (typ.): 0.8 A @ 115 VAC / 0.4 A @ 230 VAC / 0.32 A @ 277 VAC Inrush current (typ.): cold start, 50 A @ 230 VAC (≈270 μs at 50 % Ipeak) Leakage current: < 0.25 mA @ 277 VAC Overload protection: 108 – 130 % of rated output power, hiccup mode, auto recovery Overvoltage protection: Shut down output voltage, re‑power on to recover Overtemperature protection: Shut down output voltage, re‑power on to recover (DA2: hiccup mode) Short‑circuit protection: Hiccup mode, auto recovery Operating temperature (case Tcase): −40 °C to +85 °C (see “Output load vs temperature” derating) Operating humidity: 20 – 95 % RH, non‑condensing Storage temperature / humidity: −40 °C to +80 °C, 10 – 95 % RH Temperature coefficient: ± 0.03 % / °C (0 – 50 °C) Vibration: 10 – 500 Hz, 5 G, 12 min./cycle, 72 min. along X, Y, Z axes Withstand voltage: 3.75 kVAC (input–output), 1.5 kVAC (input–DA), 1.5 kVAC (output–DA) Isolation resistance: > 100 MΩ @ 500 V DC, 25 °C, 70 % RH Safety standards: UL8750 (type “HL”, except DA), UL879 (12 V, 24 V Blank only), ENEC EN 61347‑1, EN 61347‑2‑13 (independent), EN 62384, BIS IS 15885 (Part 2/Sec 13; 12/24/48 Blank & 12/24‑DA2), EAC TP TC 004, GB19510.1, GB19510.14; IP67; suitable for emergency installations per EN 61347‑2‑13 Annex J (EL) DALI standards (DA/DA2): IEC 62386‑101/102/207/251, Device Type 6 (DT6) EMC emission: EN 55015, EN 61000‑3‑2 Class C (≥60 % load), EN 61000‑3‑3, GB/T 17743, GB17625.1, EAC TP TC 020 EMC immunity: EN 61000‑4‑2,3,4,5,6,8,11; EN 61547 (light industry level, surge Line–Line 2 kV), EAC TP TC 020 MTBF (typ.): 2,626,600 h (Telcordia SR‑332, 25 °C) / 227,100 h (MIL‑HDBK‑217F, 25 °C) Dimensions (L x W x H): 150 mm x 53 mm x 35 mm Weight: approx. 0.49 kg Case & protection: fully encapsulated plastic case, IP67, Class II/2 No‑load power consumption: < 0.5 W Design: 60 W constant‑voltage PWM LED driver, Class 2, LPS Information about the MEAN WELL PWM-60-24 The MEAN WELL PWM‑60‑24 is a 60 W constant‑voltage LED driver with a PWM‑style output, designed to maintain brightness homogeneity when driving 24 V LED strips and other constant‑voltage LED loads. Its PWM operation at approximately 1.47 kHz (Blank/DA) or 2.5 kHz (DA2) delivers smooth, flicker‑free dimming while preserving color consistency even at low dimming levels. With typical efficiency up to around 89 %, active power factor correction and a wide 90–305 V AC input range, the driver is energy‑efficient and suitable for global installations. The fully encapsulated IP67 housing, wide −40 to +85 °C case temperature range and comprehensive protection features (short‑circuit, overload, overvoltage, overtemperature) ensure robust operation in dry, damp and wet locations, including suitability for certain emergency lighting systems under EN 61347‑2‑13. The integrated 3‑in‑1 dimming interface (0–10 V, 10 V PWM signal, resistance) in the Blank version and optional DALI/DALI‑2 control (DA/DA2 types) provide excellent flexibility for modern lighting control and building automation. Combined with long lifetime ratings and extensive international safety and EMC certifications, the PWM‑60‑24 is a strong choice for 24‑V LED strip lighting, indoor and decorative lighting, architectural lighting and industrial LED applications that require reliable constant‑voltage PWM drivers.

Technical Information & Details about the MEAN WELL LPV-100-24 Power Supply Rated output power: 100.8 W DC output voltage: 24 V DC Rated output current: 4.2 A Current range: 0 – 4.2 A Input voltage range: 90 – 264 V AC (127 – 370 V DC), 47 – 63 Hz Efficiency (typical): about 88 % Ripple & noise (max.): ≤ 150 mVp-p Output voltage range (O.V.P. region): 27.6 – 32.4 V DC Voltage tolerance: ±5.0 % Line regulation: ±2.0 % Load regulation: ±5.0 % Setup, rise time: 2000 ms, 25 ms at 230 V AC / 115 V AC (first cold start) Hold-up time (typ.): 50 ms at 230 V AC / 14 ms at 115 V AC (full load) AC input current (typ.): 2.2 A at 115 V AC / 1.2 A at 230 V AC Inrush current (typ.): 75 A at 230 V AC (cold start, twidth ≈ 700 μs) Leakage current: < 0.25 mA at 240 V AC Overload protection: 110 – 150 % of rated output power, hiccup mode, auto recovery after fault removal Overvoltage protection: shut down output voltage at 27.6 – 32.4 V, re‑power on to recover Operating temperature: −25 °C to +70 °C (derating required, see curve) Operating humidity: 20 – 90 % RH, non‑condensing Storage conditions: −40 °C to +80 °C, 10 – 95 % RH Cooling method: free air convection (fanless) Withstand voltage: 3000 V AC between input and output Isolation resistance: > 100 MΩ at 500 V DC, 25 °C, 70 % RH Ingress protection rating: IP67, fully encapsulated plastic case Dimensions (L x W x H): 190 mm x 52 mm x 37 mm Weight: approx. 610 g Vibration resistance: 10 – 500 Hz, 2 G, 60 min per axis (X, Y, Z) EMC emission: BS EN/EN 55032 Class B, BS EN/EN 61000‑3‑2 Class A (≤80 % load), BS EN/EN 61000‑3‑3 EMC immunity: BS EN/EN 61000‑4‑2,‑3,‑4,‑5,‑6,‑8,‑11; BS EN/EN 55035 Safety approvals: UL 8750, CSA C22.2 No. 250.13‑12, UL 879, CSA C22.2 No. 207‑M89, BIS IS 15885, IEC/BS EN/EN 62368‑1, EAC Case design: fully isolated, encapsulated plastic case for damp and dusty environments MTBF (typical): 4,497,100 h (Telcordia SR‑332, 25 °C) Manufacturer warranty: 2 years About the MEAN WELL LPV-100-24 The MEAN WELL LPV-100-24 is a 100 W class constant‑voltage switching power supply that provides a regulated 24 V DC output at up to 4.2 A, fully encapsulated in an IP67 plastic housing for reliable use in harsh environments. Its universal AC input range, high efficiency, short‑circuit, overload and overvoltage protection, and fanless free air convection make it suitable for indoor and sheltered outdoor applications. With compact dimensions, strong isolation and broad safety and EMC approvals, LPV-100-24 is a robust 24 V source for LED strips, signage, control systems and other low‑voltage equipment that require a rugged, dust‑ and splash‑proof power supply.

Not approved as an LED driver within the EU! An approved alternative is, for example, the LPF-60 series. Technical Information & Details of the MEAN WELL LPV-60-24 Power Supply Output Power: 60 W Output Voltage: 24 V DC Output Current: 2.5 A Input Voltage Range: 90 – 264 V AC / 127 – 370 V DC, 47 – 63 Hz Efficiency: up to 86 % Ripple & Noise: ≤ 150 mVp-p Inrush Current: max. 60 A @230 VAC No-load Power Consumption: < 0.5 W Operating Temperature: −30 °C to +70 °C Cooling: fanless natural convection Protection Features: Short-circuit, Overload, Overvoltage Overvoltage Category: OVC III Isolation Voltage: 3000 V AC between input and output Dimensions (H x W x D): 32 mm x 42.5 mm x 162.5 mm Weight: approx. 420 g Safety & EMC Certificates: CE, UL1310, TUV, CB, EAC, IP67 LED Indicator: - Manufacturer Warranty: 2 years Information about the MEAN WELL LPV-60-24 The MEAN WELL LPV-60-24 is a powerful LED power supply with 60 W and stable 24 V DC / 2.5 A output voltage. It excels with excellent efficiency up to 86 %, fanless convection cooling for silent operation, and a fully waterproof IP67 housing. The comprehensive protection features (short-circuit, overload, and overvoltage protection) with automatic recovery ensure maximum operational safety. Perfect for LED strips, modules, outdoor lighting, and humid environments – the universal input voltage range 90–264 V AC enables worldwide deployment. With international certifications, the LPV-60-24 offers maximum flexibility, durability, and weatherproof protection in demanding environments.

Technical Information & Details on MEAN WELL PWM-200-24 Power Supply Output Power: 200 W Output Voltage: 24 V DC Output Current: 8.3 A Input Voltage Range: 100 – 305 V AC / 142 – 431 V DC, 47 – 63 Hz Efficiency: up to 93 % PWM Frequency: 4 kHz Inrush Current: typ. 65 A Standby Power Consumption: 0.5 W Operating Temperature: −40 °C to +80 °C Cooling: IP67 waterproof, natural convection Protection Functions: Short circuit (Hiccup or Constant Current Limiting, auto recovery), Overload, Overvoltage, Over temperature Isolation Voltage: 3.75 kV AC between input and output Dimensions (L x W x H): 195 mm x 68 mm x 39.5 mm Weight: approx. 1.03 kg Safety & EMC Certifications: UL8750, ENEC BS EN 61347-1/-2-13, IP67, EAC, IS 15885 Dimming: 3-in-1 (0-10V, PWM, Resistance) Manufacturer Warranty: 5 years Information on MEAN WELL PWM-200-24 The MEAN WELL PWM-200-24 is a robust 200W PWM LED driver with IP67 water protection, reliably operating year-round from -40 °C to +80 °C and optimized for harsh environments. It scores with excellent efficiency up to 93%, minimal standby draw of 0.5 W, and a universal 3-in-1 dimming system for precise control. Ideal for premium LED projects, area, and outdoor lighting, including advanced protections and lifespan over 2,235,000 hours.